Why does my cabrio washer says ul?

If uL (unbalanced load) appears in display, the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue.

How do I fix error code uL?

UL is the code for unbalanced load. Open the lid and redistribute your wash to balance the weight of the wet items, then restart the machine. Repeat until the washer spins without thumping.

How do you fix the uL code on a Cabrio washer?

Whirlpool Cabrio Washer uL Code Troubleshooting – YouTube

How do I fix the code on my Whirlpool Cabrio?

Always disconnect the washing machine’s power supply before working on the appliance! First press PAUSE/CANCEL once to clear the Fault code from the Cabrio display. If code appears again put it through an automatic diagnostic cycle while you enjoy a nice soothing cup of tea.

What does uL mean on my washing machine?

uL. (none) Unbalanced load. uL is displayed when the machine/motor control detects an off-balance load and remains on while the washer runs a mini-cycle to rebalance the load.

Why is my washer always unbalanced?

The most likely culprit is the suspension rods. These rods help to limit the amount of side to side and front to back movement that happens when a washer enters the spin cycle. … If your washer is manifesting the banging noise of an unbalanced load with every spin cycle, contact us today.

How do you fix an unbalanced drum on a washing machine?

How to Diagnose Drum Problems in a Washing Machine – YouTube

How do you balance a washing machine?

How To Balance an Old Washing Machine – YouTube

Can you reset a Whirlpool Cabrio washing machine?

How To Reset Whirlpool Cabrio Washer: Turn the washer off. … Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.

How do I clean my Whirlpool Cabrio washer?

Clean Whirlpool Cabrio HE Washer Using Natural Ingredients – YouTube

How do I find the codes on a Whirlpool Cabrio washer?

Washing Machine Diagnostic Test &amp, Error Codes (Cabrio, Bravo

What does UL mean on electrical equipment?

UL stands for Underwriter Laboratories, a third-party certification company that’s been around for over a century. UL was founded in 1894 in Chicago. They certify products with the aim to make the world a safer place for both workers and consumers.

Why is my Whirlpool washer unbalanced?

If the shock dampening device is broken, the tub might become unbalanced, causing it to shake and vibrate during the spin cycle. … If the tub wear pad is worn out or missing, the washer will vibrate or shake during operation. Inspect the tub wear pad. If the tub wear pad is worn out or missing, replace it.

How do I fix the UL code on my Kenmore washer?

You can try to clear the Error Codes, Unplug the washer for 1 to 2 minutes. Disconnect the U.I. (touch pad). Plug the washer back in for 1 to 2 minutes.

Should my washing machine drum wobble?

Sometimes, your washer will vibrate and there’s nothing particularly wrong. Washers do tend to wiggle a small amount when the drum spins, especially during high-speed spin cycles. This can be considered normal, but it can also be unpleasantly noisy or shake nearby objects.

How do I know if my washing machine balance ring is bad?

The balance ring is filled with fluid. This fluid helps to dampen the vibration of the washer. If this fluid leaks out of the balance ring, the washer tub will vibrate and shake during operation. Check the balance to determine if is still filled with fluid.

How do you know if your washing machine drum is broken?

6 signs it’s time to replace your washing machine

  1. It’s not kind to your clothes… or the environment. …
  2. The drum won’t spin at the end of the cycle. …
  3. The machine still works but the water hasn’t drained. …
  4. It’s more noisy than it should be. …
  5. It’s no longer big enough for your family. …
  6. It’s much older than your latest smartphone.

Why is my washing machine shaking violently?

Possible Cause: Unbalanced Washer

If the washing machine is not balanced, it may shake violently during the spin cycle, causing water to spill on the floor. Redistributing the load will usually solve this issue if the cause is due to too many clothes on one side of the unit.

How do you balance a washer drum?

Home Maintenance : How to Balance a Washing Machine Tub – YouTube

How do you fix an off balance front load washer?

Level your washer by putting 4 towels in the washer and put the washer in spin. Wait until it gets to high spin and adjust the front legs to level your front load washer. The out of balance issue will smooth out by turning the legs to touch the floor in an even manner.

How do I reset the control panel on my Whirlpool washer?

Follow these steps to reset a Whirlpool washing machine: Make sure the power to the washer is turned on at the wall, but keep the Power button on the control off. Hold the Program button down while simultaneously pressing the Water Level button two times. When done correctly, the control panel lights should illuminate.

How do you reset the sensor on a Whirlpool washing machine?

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

How do you do a factory reset on a washing machine?

To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.

How do I clean the filter on my Whirlpool Cabrio washer?

Whirlpool washers – How to clean the filters? – YouTube

How do I clean the filter on my Whirlpool top load washer?

How To: Whirlpool/KitchenAid/Maytag Washer Filter Plug Kit 285868

How do you clean the filter on a Whirlpool top load washer?

4 Steps to Clean a Whirlpool Washing Machine Filter

  1. Step 1: Locate the filter. Your first step is to find the filter’s location. …
  2. Step 2: Pull It Out. …
  3. Step 3: Scrub the Filter. …
  4. Step 4: Don’t Forget About the Inside!

How do I put my Whirlpool washer in diagnostic mode?

Whirlpool top load washer diagnostic led code #whirlpool #Toploader …

Is UL required?

Having a UL listed certified unit is not legally required. It is, however, a common practice because many large companies will only buy equipment that has passed the UL safety tests. … Having a tested product shows that the equipment meets a nationally recognized safety standard.

What does UL code mean?

Your washer is off balance or the load is unbalanced

If uL (unbalanced load) appears in display, the load is out of balance.

What is UL code?

&lt,ul&gt, HTML Tag

The &lt,ul&gt, element is used to define an unordered list of items. Use an unordered list to contain &lt,li&gt, elements that do not need to be presented in numerical order and can be rearranged without changing the meaning of the list.

Why is my washer drum loose banging around?

Most of the time, washers make banging sounds because the drum is off-balance, but sometimes it’s the entire washer. If one of your washer feet is too short or on uneven ground, your washer may wobble during the spin cycle. This wobble can cause two different kinds of banging.

How do you change a balance ring on a washing machine?

How To: Whirlpool/KitchenAid/Maytag Balance Ring WP387240 – YouTube

How do you reset the sensor on a Kenmore washing machine?

To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.

How do I reset my Kenmore 700 Series washer?

Most washer’s can be reset like a personal computer. Unplug or turn the circuit breaker off for 30 seconds. Plug the power cord into the wall outlet or turn the breaker back on and wait 30 seconds. Press the Pause / Cancel / Stop button twice to clear the display.

How do I reset my Kenmore Elite Oasis washer?

The only way to reset a washer, is to disconnect it from the outlet or switch off the designated home circuit breaker for 20-30 minutes, then restore the power. If the washer won’t drain then it will not be able to go into spin so if you fix the no drain problem the spin problem may take care of itself.

How do I stop my Whirlpool washer from shaking?

If you notice your Whirlpool washer vibrates on spin cycle, the washer may not be level. Thankfully, washing machines use adjustable legs to help level it out. Solution: Use a level to check the washer. Adjust the legs accordingly by twisting the bottom “feet” of the washer.

How does a balance ring work?

The balance ring is an enclosed plastic container that is partially filled with a salt water solution. The two halves of the balance ring are welded together to form a permanent seal. It is attached to the inner clothes basket and allows the basket to spin smoothly if an uneven load creates an out-of-balance situation.

How does a front-load washer balance ring work?

The balance ring is a fluid filled ring at the top of the tub. As the load shifts during wash, the load may become more concentrated on one side of the basket. The fluid in the balance ring shifts to the opposite side of the load to help offset the weight of the load and keep the rotation of the basket stable.